| |
Solenoid Control
Electronics
|
Please use the following comparison table to find the product
that meets your requirements.
 |
Item Number |
Series |
Input Signal |
Controller |
Driver |
Power Supply |
Number of Devices |
1
|
Pick and Hold Module
 |
Requires External Pulse
Input |
- |
Yes |
External |
Up to 2 |
The
Pick and Hold
Solenoid Driver Module is designed to avoid
over heating of the solenoid coil once it is energized.
This product has been
featured on Sensors Online and
Product Design & Development.
|
 |
Item Number |
Series |
Input Signal |
Controller |
Driver |
Power Supply |
Number of Devices |
2
|
PWM Module
 |
0-5
VDC Input Signal
|
- |
Yes |
External |
Up to 2 |
0-10
VDC Input Signal
|
4-20 milliamps
Input Signal |
Step and Direction Input Signals |
Quadrature Input Signals |
External Potentiometer |
Onboard Potentiometer |
The PWM Module is designed to enable the user to vary
the voltage across a solenoid or other devices.
The PWM output voltage is
proportional to the input control voltage.
|
 |
Item Number |
Series |
Input Signal |
Controller |
Driver |
Power Supply |
Number of Devices |
3
|
Closed
Loop Solenoid Process Control Module
 |
0-5 VDC Input Signal
|
- |
Yes |
External |
1 |
0-10 VDC Input Signal
|
Phase-A and
Phase-B Quadratue Signals |
Step and
Direction |
0-20
milliamps Input Signal |
External Potentiometer |
This module offers a very low cost solution for limited angle / stroke
position control.
The Closed Loop Solenoid Process Control Module is designed to
control the position of a solenoid plunger / shaft, voice coil
motor or similar
devices.
|
 |
Item Number |
Series |
Input Signal |
Controller |
Driver |
Power Supply |
Number of Devices |
4
|
Pick and Drop Module
 |
Requires External Trigger
Input |
- |
Yes |
External |
Up to 2 |
The Pick and Drop Driver Module applies a
single pulse to the device, then drops the supply voltage to zero.
|
 |
Item Number |
Series |
Input Signal |
Controller |
Driver |
Power Supply |
Number of Devices |
5
|
Load On-Off Power Cycling Module
 |
Not
Required |
Built-in Signal Generator |
Yes |
External |
Up to 2 |
The Load On-Off Cycling Module is designed to enable
the user to cycle the voltage across a solenoid or other devices.
The
frequency of actuation, the output
peak voltage. and the duty cycle of
the actuation (ratio of on time to the length of one full cycle) are
adjusted using the onboard potentiometer. |
 |
Item Number |
Series |
Input Signal |
Controller |
Driver |
Power Supply |
Number of Devices |
7
|
Serially Controlled Solenoid Driver |
Externally Controlled |
Yes |
Yes |
External |
Up to
2 |
The solenoid
control card is an
easy-to-use, plug-and-play
and
cost effective
solution for single or dual device solenoid control
applications. It may be used as a stand-alone unit or
may be commanded by an external device. |
 |
Item Number |
Series |
Input Signal |
Controller |
Driver |
Power Supply |
Number of Devices |
8
|
Solenoid Commander
Card
|
Externally Controlled
Stand-alone |
Yes |
- |
External |
Up to
24 |
|
 |
Item Number |
Series |
Input Signal |
Controller |
Driver |
Power Supply |
Number of Devices |
9
|
Solenoid
Control Module
|
Externally Controlled
Stand-alone |
Yes |
Yes |
External |
Up
to 16 |
The compact and stand-alone unit consists of controller and the drivers. |
 |
Item Number |
Series |
Input Signal |
Controller |
Driver |
Power Supply |
Number of Devices |
10
|
Solenoid Control System
 |
Externally Controlled
Stand-alone |
Yes |
Yes |
Built-in |
Up
to 32 |
The compact and stand-alone unit consists of controller,
drivers and the power supplies. |
 |
Item Number |
Series |
Input Signal |
Controller |
Driver |
Power Supply |
Number of Devices |
12
|
DIN Rail Mount
Bracket |
- |
- |
- |
- |
- |
The bracket
is used to mount our solenoid drivers to a DIN rail. |
 |
Item Number |
Series |
Input Signal |
Controller |
Driver |
Power Supply |
Number of Devices |
13
|
Two-axis Joystick |
- |
- |
- |
- |
- |
|
 |
Item Number |
Series |
Input Signal |
Controller |
Driver |
Power Supply |
Number of Devices |
14
|
Three-axis
Joystick |
- |
- |
- |
- |
- |
|
 |
Item Number |
Series |
Input Signal |
Controller |
Driver |
Power Supply |
Number of Devices |
15
|
Trackball |
- |
- |
- |
- |
- |
|
The compact and stand-alone unit consists of
controller, drivers and the power
supplies.
|