| |
Motorized Two-axis Gimbal Mount,
Pitch and Roll Axes
(Elevation and Roll Axes)
|
Home >
Assorted Motorized Gimbal Mounts |
![](pics/motorized-two-axis-gimbal-mount-360.jpg)
![](pics/motorized-two-axis-pitch-roll-gimbal-mount-270.jpg)
|
![](pics/motori8.jpg) |
The AU270-PR Motorized Three-axis Gimbal Mounts require a
Motion Controller
that can be ordered as a complete plug-and-play system with joystick, trackball, and keypad.
![](../alignment-stages/pics/index_1.jpg)
Video Description
|
Specifications
Type |
AU270-PR |
Structure
Description |
Range of Travel |
360° Continuous
on All Axes |
Table Size |
Diameter: 7.874 in (200 mm)
|
Gear Ratio |
180:1 |
Actuator Type |
Worm and Worm Gear |
Travel Guide |
Precision V-groove & Crossed Roller |
Aperture Diameter |
90 mm |
Elevation Motor
![](../motorized-linear-stages/low-cost-series/pics/Motorized%20Linear%20Stage%20Pin%20Assignment.gif) |
Typical Phase Current |
3 Amp |
DB-9 Male Connector |
Pin Assignment and Description |
1 |
+5 VDC |
2 |
Channel-A of Encoder (Optional) |
3 |
Channel-B of Encoder (Optional) |
4 |
Common |
5 |
HOME Switch, Open Collector, Normally Open, Needs 1K Pull up Resistor |
6 |
Stepper Motor Phase A+ |
7 |
Stepper Motor Phase A- |
8 |
Stepper Motor Phase B+ |
9 |
Stepper Motor Phase B- |
|
Roll Motor
![](../motorized-linear-stages/low-cost-series/pics/Motorized%20Linear%20Stage%20Pin%20Assignment.gif) |
Typical Phase Current |
3 Amp |
DB-9 Male Connector |
Pin Assignment and Description |
1 |
+5 VDC |
2 |
Channel-A of Encoder (Optional) |
3 |
Channel-B of Encoder (Optional) |
4 |
Common |
5 |
HOME Switch, Open Collector, Normally Open, Needs 1K Pull up Resistor |
6 |
Stepper Motor Phase A+ |
7 |
Stepper Motor Phase A- |
8 |
Stepper Motor Phase B+ |
9 |
Stepper Motor Phase B- |
|
Base Material |
Aluminum Alloy |
Surface Treatment |
Black Anodized |
Load Capacity |
10 kg (22 lb) |
Weight |
35 kg (77 lb) |
Resolution |
0.001° = 3.6 arcsec (10 Micro-steps per Step Motor Driver in use) |
Maximum Speeds of the Elevation and Roll Axes with Stepper Motors |
8 °/sec |
Maximum Speed of the Azimuth axis with Servo Motor |
45 °/sec |
Maximum Speed of the Elevation and Roll Axes with Servo Motors |
45 °/sec |
Typical Accuracy
|
Accuracy |
0.05° = 180 arcsec |
Repeatability |
+/-
0.01° = +/- 36 arcsec |
|
|
|
Ordering Information
Part No. |
Description |
Amount |
AU270-PR-01 |
Stepper
Motor Driven
Two-axis Gimbal Mount, Pitch and Roll Axes
(Pitch and Roll Axes) |
Click to Get a Quote |
AU270-PR-02 |
Two-axis Phase Brushless Servo Motor with Quadrature Incremental Optical Encoder Driven
Two-axis Gimbal Mount, Roll Axes
(Yaw, Pitch and Roll Axes)
|
Click to Get a Quote |
AU270-PR-03 |
DC
Servo Motor with Quadrature Incremental Optical Encoder Driven
Two-axis Gimbal Mount, Roll Axes
(Yaw, Pitch and Roll Axes)
|
Click to Get a Quote |
AU270-PR-04 |
Stepper
Motor Driven
Two-axis Gimbal Mount,
Roll Axes
(Yaw, Pitch and Roll Axes) with
500 Cycles per Revolution Quadrature Optical Encoders
Mounted at the back of the Stepper
Motors |
Click to Get a Quote |
|
|