|
| |
|
Motorized Two-axis Gimbal Mount,
Elevation and Roll Axes
( Pitch and Roll Axes)
|
|
Home >
Assorted Motorized Gimbal Mounts |
|
Specifications
| Type |
AU270-ER |
|
Structure
Description |
Range of Travel |
360° Continuous
on All Axes |
| Table Size |
Diameter: 3.937 in (100 mm)
|
| Gear Ratio |
180:1 |
| Actuator Type |
Worm and Worm Gear |
| Travel Guide |
Precision V-groove & Crossed Roller |
Aperture Diameter |
30 mm |
|
Elevation Motor
 |
| Typical Phase Current |
3 Amp |
|
DB-9 Male Connector |
|
Pin Assignment and Description |
|
1 |
+5 VDC |
|
2 |
Channel-A of Encoder (Optional) |
|
3 |
Channel-B of Encoder (Optional) |
|
4 |
Common |
|
5 |
HOME Switch, Open Collector, Normally Open, Needs 1K Pull up Resistor |
|
6 |
Stepper Motor Phase A+ |
| 7 |
Stepper Motor Phase A- |
| 8 |
Stepper Motor Phase B+ |
| 9 |
Stepper Motor Phase B- |
|
|
Roll Motor
|
| Typical Phase Current |
1 Amp |
|
DB-9 Male Connector |
|
Pin Assignment and Description |
|
1 |
+5 VDC |
|
2 |
Channel-A of Encoder (Optional) |
|
3 |
Channel-B of Encoder (Optional) |
|
4 |
Common |
|
5 |
HOME Switch, Open Collector, Normally Open, Needs 1K Pull up Resistor |
|
6 |
Stepper Motor Phase A+ |
| 7 |
Stepper Motor Phase A- |
| 8 |
Stepper Motor Phase B+ |
| 9 |
Stepper Motor Phase B- |
|
| Base Material |
Aluminum Alloy |
| Surface Treatment |
Black Anodized |
| Load Capacity |
10 kg (22 lb) |
| Weight |
|
Resolution |
0.001° = 3.6 arcsec (10 Micro-steps per Step Motor Driver in use) |
|
Maximum Speeds of the Elevation and Roll Axes with Stepper Motors |
8 °/sec |
|
Maximum Speed of the Azimuth axis with Servo Motor |
45 °/sec |
|
Maximum Speed of the Elevation and Roll Axes with Servo Motors |
45 °/sec |
|
Typical Accuracy
|
|
Accuracy |
0.05° = 180 arcsec |
|
Repeatability |
+/-
0.01° = +/- 36 arcsec |
|
|
|
Ordering Information
|
Part No. |
Description |
Amount |
|
AU270-ER-01 |
Stepper
Motor Driven
Two-axis Gimbal Mount, Elevation and Roll Axes
(Yaw, Pitch and Roll Axes) |
Click to Get a Quote |
|
AU270-ER-02 |
Three Phase Brushless Servo Motor with Quadrature Incremental Optical Encoder Driven
Two-axis Gimbal Mount, Elevation and Roll Axes
(Yaw, Pitch and Roll Axes)
|
Click to Get a Quote |
|
AU270-ER-03 |
DC
Servo Motor with Quadrature Incremental Optical Encoder Driven
Two-axis Gimbal Mount, Elevation and Roll Axes
(Yaw, Pitch and Roll Axes)
|
Click to Get a Quote |
|
AU270-ER-04 |
Stepper
Motor Driven
Two-axis Gimbal Mount,
Elevation and Roll Axes
(Yaw, Pitch and Roll Axes) with
500 Cycles per Revolution Quadrature Optical Encoders
Mounted at the back of the Stepper
Motors |
Click to Get a Quote |
|
|
