|
|
These
motorized
positioning tables
are made of
aluminum
alloy with
an elegant
black
anodized
surface.
They provide
up to 1000
mm of
travel.
The drive
mechanism is
high precision
crossed roller.
These
linear
stages are
also
available
with a servo
motors and
optical
encoders.
The knob mounted on the motors allow for manual adjustment.
These knobs may be replaced with an optical encoders for precision position verification.
This
series requires a
Motion Controller
that can be
ordered as a
complete
plug-and-play
system with
RS-232, USB,
joystick,
trackball,
and keypad
control. |
|
Specifications
|
Structure
Description |
Travel |
|
Range of
Travel (mm) |
Pitch of Lead
Screw |
Resolution |
| 15 |
1
mm per turn |
0.5 microns (10 Micro-steps per Step Motor Driver in use) |
| 30 |
1
mm per turn |
0.5 microns (10 Micro-steps per Step Motor Driver in use) |
| 50 |
1
mm per turn |
0.5 microns (10 Micro-steps per Step Motor Driver in use) |
| 75 |
1
mm per turn |
0.5 microns (10 Micro-steps per Step Motor Driver in use) |
| 100 |
4
mm per turn |
2 microns (10 Micro-steps per Step Motor Driver in use) |
| 150 |
4
mm per turn |
2 microns (10 Micro-steps per Step Motor Driver in use) |
| 200 |
4
mm per turn |
2 microns (10 Micro-steps per Step Motor Driver in use) |
| 300 |
4
mm per turn |
2 microns (10 Micro-steps per Step Motor Driver in use) |
| 400 |
4
mm per turn |
2 microns (10 Micro-steps per Step Motor Driver in use) |
| 500 |
4
mm per turn |
2 microns (10 Micro-steps per Step Motor Driver in use) |
| 600 |
4
mm per turn |
2 microns (10 Micro-steps per Step Motor Driver in use) |
| 700 |
4
mm per turn |
2 microns (10 Micro-steps per Step Motor Driver in use) |
| 800 |
4
mm per turn |
2 microns (10 Micro-steps per Step Motor Driver in use) |
| 900 |
4
mm per turn |
2 microns (10 Micro-steps per Step Motor Driver in use) |
| 1000 |
4
mm per turn |
2 microns (10 Micro-steps per Step Motor Driver in use) |
|
| Travel Guide |
High Precision Crossed Roller |
|
DB-9 Male Connector
 |
| |
|
Typical Phase Resistance
|
3.8 Ohms, Bi-directional |
| Typical Phase Current |
1 Amp |
| |
|
Pin Assignment and Description |
| 1 |
+5 VDC for the Limit Sensors |
| 2 |
CW Limit Switch, Open Collector, Normally Open, Needs Pull up Resistor (1000 Ohms)
|
| 3 |
CCW Limit Switch, Open Collector, Normally Open, Needs Pull up Resistor (1000 Ohms)
|
| 4 |
Return for+5 VDC |
|
5 |
Not Connected |
|
6 |
Stepper Motor Phase A+ |
| 7 |
Stepper Motor Phase A- |
| 8 |
Stepper Motor Phase B+ |
| 9 |
Stepper Motor Phase B- |
|
| Body Material |
Aluminum Alloy |
| Surface Treatment |
Black Anodized |
|
Typical Accuracy
|
Resolution |
Configuration Dependent |
| Maximum Speed with Stepper Motor |
5 mm / sec |
|
Maximum Speed with Servo Motor |
|
| Repeatability |
1 microns |
| Positional Accuracy |
10 microns |
|
Accessories
Description
|
Optional Optical Encoders
Optional Servo Motors
Other Sizes and Strokes Available |
|
Ordering
Information
|
|
