|
| |
Motorized Single-axis Table
|
|
Home >
Motorized Linear Actuators
>
Low Cost Linear
Single-axis Stages |
|
|
|
This
motorized
positioning table
is made of
aluminum
alloy with
an elegant
black
anodized
surface.
It provides
100 mm of
travel at
a Maximum
Speed with
Stepper
Motor of
40 mm per
second.
The drive
mechanism is
lead screw.
The bench
size is 120
X 120 mm and
has a body
weight of
3.4 Kg.
The maximum
load of this
stage
table is 30
Kg.
The
resolution
of 2 microns is
achieved
with a 10
micro-steps
per step
stepper
motor
driver. This
linear
stage is
also
available
with a Three
Phase
Brushless
Servo Motor
and Optical
Encoder (-02
Version)
The knob mounted on the motor allows for manual adjustment. This knob may be replaced with an
Optical
Encoder (-04
Version) for precision position verification.
This
stage requires a
Motion Controller
that can be
ordered as a
complete
plug-and-play
system with
RS-232, USB,
joystick,
trackball,
and keypad
control. |
|
Specifications
| Type |
AQ140-100 |
|
Structure
Description |
Travel |
100 mm |
| Stage Size |
120×120 mm |
| Lead Screw Pitch |
4 mm per turn |
| Travel Guide |
High Precision Linear Ball Bearing |
 |
|
Two-Phase Stepper Motor (1.8°) |
|
Typical Phase Resistance
|
3.8 Ohms, Bi-directional |
| Typical Phase Current |
1 Amp |
|
DB-9 Male Connector |
|
Pin Assignment and Description |
|
1 |
+5 VDC |
|
2 |
Far End Limit Switch,
Open Collector or Normally Open
Needs Pull up Resistor (1000 Ohms)
Approximately 5.5 mm away from Far End Hard Stop |
|
3 |
Near Motor Limit Switch
Open Collector or Normally Open
Needs Pull up Resistor (1000 Ohms)
Approximately 47 mm away from Motor Side Hard Stop
|
|
4 |
Return for+5 VDC |
|
5 |
Not Connected |
|
6 |
Stepper Motor Phase A+ |
|
7 |
Stepper Motor Phase A- |
|
8 |
Stepper Motor Phase B+ |
|
9 |
Stepper Motor Phase B- |
|
|
| Body Material |
Aluminum Alloy |
| Surface Treatment |
Black Anodized |
| Load capacity |
30 Kg |
| Weight |
3.4 kg |
|
Typical Accuracy
|
Resolution |
Control Electronics Dependent, 2 microns with 10 Micro-steps per Step Motor Driver in use
1 micron with 10 Micro-steps per Step Motor Driver in use |
| Maximum Speed with Stepper Motor |
80 mm/sec |
| Maximum Speed with Servo Motor |
|
| Positioning Accuracy |
10 microns |
|
Accessories
Description
|
| Optical Encoder (-04 Version) |
Three Phase Brushless Servo Motor and Optical Encoder (-02 Version)
|
|
Stepper Motor Driven Mechanical Drawing
Click to get the STEP file
|
|
|
Ordering Information
|
Part No. |
Description |
Amount |
|
AQ140-100-01 |
Stepper Motor Driven Linear Single-axis Stage, Travel
: 100 mm |
Click to Get a Quote |
|
AQ140-100-02 |
Three Phase Brushless Servo Motor with Quadrature Incremental
Optical Encoder Driven Linear Single-axis Stage, Travel
: 100 mm |
Click to Get a Quote |
|
AQ140-100-03 |
DC Servo Motor with Quadrature Incremental
Optical Encoder Driven Linear Single-axis Stage |
Click to Get a Quote |
|
AQ140-100-04 |
Stepper Motor Driven
Linear Single-axis Stage with 500 Cycles per Revolution
Quadrature Optical Encoder Mounted at the back
of the Stepper Motor |
Click to Get a Quote |
|
|
