|
| |
Motorized Single-axis Table
|
|
Home >
Motorized Linear Actuators
>
Low Cost Linear
Single-axis Stages
|
|
|
|
This
motorized
positioning table
is made of
aluminum
alloy with
an elegant
black
anodized
surface.
It provides
300 mm of
travel at
a Maximum
Speed with
Stepper
Motor of
40 mm per
second.
The drive
mechanism is
lead screw.
The bench
size is 150
X 100 mm and
has a body
weight of
5.5 Kg.
The maximum
load of this
stage
table is 30
Kg.
The
resolution
of 2 microns is
achieved
with a 10
micro-steps
per step
stepper
motor
driver. This
linear
stage is
also
available
with a Three
Phase
Brushless
Servo Motor
and Optical
Encoder (-02
Version)
The knob mounted on the motor allows for manual adjustment. This knob may be replaced with an
Optical
Encoder (-04
Version) for precision position verification.
This
stage requires a
Motion Controller
that can be
ordered as a
complete
plug-and-play
system with
RS-232, USB,
joystick,
trackball,
and keypad
control.
|
|
Specifications
| Type |
AQ130-300 |
|
Structure
Description |
Travel |
300 mm |
| Stage Size |
150×100 mm |
| Lead Screw Pitch |
4 mm per turn |
| Travel Guide |
High Precision Linear Ball Bearing |
| Motor |
Two-Phase Stepper Motor (1.8°) |
| Body Material |
Aluminum Alloy |
| Surface Treatment |
Black Anodized |
| Load capacity |
30 kg |
| Weight |
6.6 kg (14.5 lb) |
|
Typical Accuracy
|
 |
|
Two-Phase Stepper Motor Typical Phase Resistance
|
3.8 Ohms, Bi-directional |
| Typical Phase Current |
1 Amp |
|
DB-9 Male Connector |
|
Pin Assignment and Description |
| 1 |
+5 VDC for the Limit Sensors |
| 2 |
Far End Limit Switch Limit Switch when the table moves away from the motor, Open Collector, Normally Open, Needs Pull up Resistor (1000 Ohms)
|
| 3 |
Near Motor Limit Switch Limit Switch, when the table moves towards the motor Open Collector, Normally Open, Needs Pull up Resistor (1000 Ohms)
|
| 4 |
Return for+5 VDC |
|
5 |
Not Connected |
|
6 |
Stepper Motor Phase A+ |
| 7 |
Stepper Motor Phase A- |
| 8 |
Stepper Motor Phase B+ |
| 9 |
Stepper Motor Phase B- |
|
|
Resolution |
Control Electronics Dependent, 2 microns with 10 Micro-steps per Step Motor Driver in use
1 micron with 10 Micro-steps per Step Motor Driver in use |
| Maximum Speed with Stepper Motor |
25 mm/sec |
| Maximum Speed with Servo Motor |
|
| Positioning Accuracy |
10 microns |
|
Accessories
Description
|
| Optical Encoder (-04 Version) |
Three Phase Brushless Servo Motor and Optical Encoder (-02 Version)
|
|
|
|
|
Ordering Information
|
Part No. |
Description |
Amount |
|
AQ130-300-01 |
Stepper Motor Driven Linear Single-axis Stage, Travel
: 300 mm |
Click to Get a Quote |
|
AQ130-300-02 |
Three Phase Brushless Servo Motor with Quadrature Incremental
Optical Encoder Driven Linear Single-axis Stage, Travel
: 300 mm |
Click to Get a Quote |
|
AQ130-300-03 |
DC Servo Motor with Quadrature Incremental
Optical Encoder Driven Linear Single-axis Stage |
Click to Get a Quote |
|
AQ130-300-04 |
Stepper Motor Driven
Linear Single-axis Stage with 500 Cycles per Revolution
Quadrature Optical Encoder Mounted at the back
of the Stepper Motor |
Click to Get a Quote |
|
|
